Font Size
S
M
L
Testimonials
Garry, Received springs this afternoon. Installed both in about an hour, no problems,Thanks.
Richard
 
Read More...

RV Hatch Motor Home Magzine

Hatchlift baggage-door gas props take the frustration and headache out of exterior compartment access

by Bill and Jenn Gehr photos by Jenn Gehr

A ccess to the myriad miscellaneous items and whatnots that are in stor- age just behind those tempera- mental exterior compartments has been a major contributing factor to countless headaches — both metaphorical and physical. And unfortunately, the last 20 years have brought few advances to these standard exterior compartment door hard- ware, until now. A new retrofitted door-lift system, called Hatchlift, helps to keep those compartment doors in place when accessing storage.

Our fifth-wheel trailer has a bedroom slide that had prevented the use of a bag- gage door catch, because the slide would not allow the compartment door to fully open. Years ago, we tried to fix the problem with a bit of creative engineering and a thin piece of stainless-steel safety wire. Grant- ed, our little invention was effective at times, but as soon as the wind was any- thing more than a slight breeze, I would end up with a bump on my skull and a few choice words that would only get me in trouble. It was time to install a fail-proof system to keep those doors in place, and Hatchlift was the perfect solution.

1) Measure 4 inches from the top edge of the door for the leading edge of the mounting plate. 2) With the mounting plate held into position, pencil a line around the outside edge. 3) Using the scuff pad, rough up the outlined area for the first step of

The simple design of the Hatchlift in- cludes a gas prop (spring assembly), two brackets, a black nylon pull strap for tall doors, screws and a specialized mounting plate. Most baggage doors are made with a foam center with little or no wood to attach any type of a brack- et with screws. Hatchlift’s pre-drilled, square-mounting plate completely solves this problem.
Installing the kit should take place when the ambient temperature is 65° F or higher, to ensure a proper bond with the aggressive adhesive tape that’s used on the backside of the mounting plate. You’ll need an assistant to get started, because the door must be held

in place at the recommended 130-170 degrees so that reference markings can be made 6 inches from the top and 2 inches from the edge on the inside face of the door. Once that’s done, the spring assembly with the upper and lower brackets in place is held in position to make sure it will clear any obstructions. If it doesn’t, the gas prop can be in- stalled on the opposite side of the door. Once clearance has been established, the bottom bracket is installed on the wall (or door jamb, if necessary) using the supplied screws.
The top bracket is attached to a mounting plate, which provides a very strong foundation. The leading edge of

the mounting plate is attached to the face of the door, 4 inches from the top, which should cover your reference marks. I recommend that you hold the gas prop assembly in place once again to be certain it has complete clearance, top and bottom. Using the supplied pad, scuff the area where the plate is to be mounted, then clean it with rubbing al- cohol and allow it to dry. The next step is to crush the tube of primer at the small black dot and apply the entire contents to the location of the scuffed, prepped area. It takes about 10 minutes for the primer to completely dry.
The exact placement of the mount- ing plate is critical, as you will only have

4) Next,follow the instructions provided and apply the primer to the roughed-up area. 5) Peel off the protective film on the mounting plate.

6) Align the plate carefully, press and hold into place. 7) Using the provided self-tapping screws, drive the screws into place but do not tighten with a drill motor; you should hand tighten with a screwdriver to avoid stripping the screws or overtightening.

one chance for proper installation. Hold the plate firmly against the door for a full minute. The next step is to install the 1/ 2-inch self-tapping screws through the mounting plate’s pre-drilled holes. Be sure to hand tighten only. The screws help hold the plate in position while the adhesives cure over the requisite 48-72 hours. Once that’s done, it’s time to in- stall the curved mounting bracket, pre- drilling the mounting plate with a 1/8- inch drill bit, which is not included. Then, attach the gas prop to the upper and lower bracket, being certain both ends are engaged firmly on the ball studs. To be sure the newly installed Hatchlift is working properly, open and close the baggage door only once or twice. Then remove the gas prop and allow the Hatchlift mounting plate to fully cure without being under a load. If needed, install the hatch strap to the backside of the baggage door lock with the provided screw. In some cases you

may need to install shims, blocks or al- ternate brackets to best accommodate the lower bracket location.
   The installation of the first Hatchlift spring assembly to a baggage door takes about an hour, but once you’ve be- come familiar with the process, installa- tion time will reduce by about 15 min- utes. Last-minute changes were made to the kits as we went to press. A second mounting stud is now included with the kit so that doors will operate under slide- outs. Also, the aforementioned shims will now be part of the kit, as will alcohol

wipes for cleaning the door face.
    Hatchlift carries a 12-month warran- ty and an msrp ranging from $31.95 to $41.95, depending on the size of the door.
   With the recent discovery of Hatch- lift for all of our RV’s baggage doors, our self-engineered compartment door holders are a thing of the past, and so are the banged heads.

Hatchlift, (303) 233-6083,
www.hatchlift.com.
Circle 214 on
Reader Service Card.

 

8) Install the upper bracket centered 6 inches from the top of the door. 9) Remove and install the shock stud into one of four adjustment holes. 10) Install the lower bracket at the predetermined position using the supplied self-tapping screws. 11)Remove the center screw from one of the baggage door locks and install the pull stap with the supplied screw

 
TrailerLife irv2.com rally 3M United States Fedex

RV Hatch Lifts

Do you own a camper or RV? You need a HatchLift for your RV safety! HatchLift will hold open your RV hatch and protect your family. HatchLift is the perfect give for the camper in your family! The hatch lift will help with lifting hatch doors and the hydraulic mechanism will hold your RV, Camper, Bus or Boat hatch open for you. RV hatch lifts supports and holds open RV Hatches safely. You need to keep your lift hatch open with hatch lifter hatch hinges to protect your health and support your hatch safely. With a hatch lift you do not have to worry about a hatch door dropping shut or hurting a member of your family. If your business needs hatch lift safety for construction workers or office personnel, turn to HatchLift! The hatch lift can hold open cabinet doors, cabinets or counters to help protect your employees from injury and reduce your liability risk. The Hatch Lift will provide you with support and safety for year round use in the camping, construction or office setting.